[scubad]

Update:

So, I was able to create a Whitelist on my firewall.  That started doing the percent adjustment but was not calculating the percentages right.  Left it alone for 2 days.  Then tonight, I changed the location to my zip code versus specifying a PWS near me.  BINGO.  I got the correct sunrise/sunset times, correct time/timezone, and the correct percentages.

Hmmm…..

Samer,  question I have a friend who has OSPi version.  Will the Arduino version get the program preview stats for the stations on the home page?

 

Thanks for all the help.

Dennis

[scubad]

I’m am seeing a TCP segment from the internet to OS.  The destination port on OS is 3040.  Which is strange cause i am doing port forwarding of just port 80.

Also, within the last 15 minutes my watering percentage changed to 21%.   Which doesn’t quite make sense if I understand the formula right.

But it is the first time it has changed….  Sunrise and Sunset are still 0600/1800.

 

 

 

 

[scubad]

Samer,

 

Are you using port 3040 for anything?

 

Dennis

[scubad]

I did a reset on the panel via B1.  Added generic config of location(changed from boston), API key and added Zimmerman.

timezone is still -5.  Sunrise/sunset is 0600 and 1800.

No Bueno.

 

[scubad]

The hard reset was power off/on.  I have removed and added the API key as well.  Let it run overnight and timezone and sunrise/sunset times were still reflecting 6am and 6pm.

My next step is clear out the whole config and default it.  Do a minimal config and see if that works and then restore the configuration.

Unless you can think of something else.  What is the possible fix coming in 2.1.4 related to the FW in your post above?

Dennis

[scubad]

I am unable to disable the FW.    I did do a quick reconfigure and disabled .1q.

No change.  Did a hard reset….

Here’s the latest pcap.

Attachments:

1. packet_capture-11.pcap_.zip

[scubad]

Here’s the pcap.  It is formatting the GET request appropriately.  The response comes back from sunrise at 390 and sunset at 1220.  But is never being set.  The capture is on the LAN side of the FW.

OS is at 192.168.1.23 and GW is 192.168.1.1

Thanks for the help.

This is frustrating me and usually i can figure these things out.

Dennis

PS.  I am consuming a lot of API requests.  Got the overage emails from wunderground yesterday and today.

 

 

Attachments:

1. packet_capture-8.pcap_.zip

[scubad]

No, the timezone is off by 1 hour.  I thought this was because the firmware doesn’t support Daylight Savings Time.  Correct?

The sunrise and sunset times are off.  I am seeing continued requests going to wunderground.  I can only do a packet capture on my Firewall for 60 seconds at a time.  Looks like every 2 1/2 minutes the unit will do a GET request to wunderground.  I will send you a pcap as a private reply.

I am using DHCP but as a fixed IP on my Meraki FW device.  GW is 192.168.1.1.  It should not be filtering anything.

 

[scubad]

Rebooted it multiple times.  maybe like 10?

 

D

[scubad]

Been reading a lot of other threads with similar issues as mine.

Thought I would post the output of my var’s.

{“fwv”:213,”tz”:20,”ntp”:1,”dhcp”:1,”ip1″:192,”ip2″:168,”ip3″:1,”ip4″:23,”gw1″:192,”gw2″:168,”gw3″:1,”gw4″:1,”hp0″:80,”hp1″:0,”hwv”:21,”ext”:1,”sdt”:0,”mas”:0,”mton”:1,”mtof”:0,”urs”:0,”rso”:1,”wl”:100,”den”:1,”ipas”:0,”devid”:0,”con”:110,”lit”:100,”dim”:15,”rlp”:0,”uwt”:1,”ntp1″:204,”ntp2″:9,”ntp3″:54,”ntp4″:119,”lg”:1,”reset”:0,”dexp”:1,”mexp”:5}

Here’s the latest output of my wundergound station near me.

&scale=0&restrict=0&tz=24&sunrise=391&sunset=1218&maxh=96&minh=46&meant=48&pre=0.380000&prec=0.480000&hc=79&eip=*removed*

I’m at a loss right now.

D

[Author]

Posts