Possible to schedule across midnight?

Because the program’s end time has to be prior to start time, what you need to do is to split the program to two the first program will start somewhere before midnight (say 9pm), and end at 11:59pm. The second program will start at 00:00am (or perhaps later if you don’t want it to start right at 00:00), and end at, say 6am. Both programs will be set to water the selected station(s) for 15 minutes, and repeat every hour. This should achieve what you need.

Hi all,
I think this is the proper topic to talk about a weird behavior on scheduling ’round midnight.

From time to time I find the from/to values of some of my programs changed to
from = 00:00
to = 00:00

This morning it happened again, and I noticed that it was a program which started at 00:01 and stopped at 08:00.
I’m not totally sure, but I suspect that the reset may be due to the 00:01 value.

I do not know if this behavior is reproducible. I will keep an eye on it.

Any other on this forum has noticed this ?

From time to time I find the from/to values of some of my programs changed to xxx

I don’t see how this can happen: because the program settings are stored in non-volatile memory, the only way the settings can change is if you modified the programs yourself. Otherwise the program settings cannot change on their own.

In the afternoon I’ve removed the battery, to control its voltage (3.2 V, viewtopic.php?f=33&t=910#p6004).

And I’m sure that this morning the program 5 was from 00:10 to 08:10. I’ve round it back at 00:10 start and 00:10 stop.

I’m underlying because this morning I checked the program, and changed the restriction from “odd days” to “None”.
Since I doubt of me, myself, my gestures (:oops:), after saving the program I checked again the start/stop values.
I did it from the mobile app.

I will try to reproduce this behaviour, be quiet until then and finally I will let you know.

I enter 08:10 in the stop field, save the program 5, see that the value is still 08:10, exit the programs page, re-enter into program page, re-open program 5 and find 00:10 in stop field back again !!

To see whether this is a UI problem, you can try to use the classic web interface (instead of the app) and see if you can reproduce the issue. To do so, open a browser and type in:
http://x.x.x.x/
where x.x.x.x is your OpenSprinkler’s IP address. This should show you the classic web UI similar to shown here:
http://rayshobby.net/?page_id=730#homepage

Try to change program settings using this web UI and see if you still get the same issue.

This morning it happened again. On program 5, start time at 00:10 and stop time at 00:10.
I’ve tried to change the stop time back to 08:10 but on web interface (now at 1.2.0b) I cannot save the correct value: I entered the 08:10 in the stop field and saved but the 00:10 value was still there after re-entering the program. After this, it was not possible to save anything with the web interface; after changing the value and pressing “save”, the wait-I-m-processing symbol appears and remained there, hanging for some minutes. I tried this 2-3 times

I finally set the correct value by the mobile app (1.2.0).

The rest of the programs were not enabled and n° 5 was the only one active.

I’m sure I did not alter anything in the program 5. Being conscious that could be me/my gestures to cause the problem, I took extra care in observing my gestures and the behavior of program 5.

This time the OS was turned on and off many times, because I had to work on the electrical system of the garden.
I will try to turn it on and off again to see if I can reproduce the problem.

Edit
I’ve checked it again with mobile app: is back to 00:10.